12V 110AH Lithium Battery For Car And Emergency Power Supply
Quick Detail for 12V 110AH Lithium Battery For Car And Emergency
Power Supply
| Battery module | 110Ahr or 1408Whr (316PCS IFR18650EC-1.4Ah cells in a 4S79P
configuration.) |
| Approx. Dimension | 260 mm x 158mm x 246 mm (L*W*H) |
| Approx. Weight | 15.1kg |
| Nominal voltage | 12.8V |
| Maximum voltage | 14.6V |
| Minimum voltage | 10.0V |
| Nominal load current | 150A max. continuous current @ 23° C |
| Peak load current | 300A max for 30 sec @ 23° C |
Specification for 12V 110AH Lithium Battery For Car And Emergency
Power Supply
No.
| Item
| General Parameter
| Remark
|
| 1 | Rated Capacity
| 110.0Ah | Standard discharge(0.2 C5)after standard charge(0.2 C5)
|
| 2 | Minimal Rated Capacity
| 105.0Ah |
| 3 | Nominal Voltage
| 12.8V | |
| 4 | Cycle Life
| Higher than 60% of the Initial Capacity of the Cells | ◆Charge: CC@0.2C to 14.6V, then CV till current to 0.05C ◆Rest: 30min. ◆Discharge: 0.2C to 10.0V ◆Temperature:20±5℃ ◆Carry out 2000cycles 100%DOD ◆Carry out 3000cycles 80%DOD ◆Carry out 3500cycles 60%DOD ◆ |
| 5 | Discharge cut-off voltage
| 10.0V |
|
| 6 | Charging cut-off voltage
| 15.6V |
|
| 7 | Cell and assembly method
| IFR18650EC-1.4AH | 4S79P |
| 8 | Housing material
| ABS+PC housing
| |
BMS Performance for 12V 110AH Lithium Battery For Car And Emergency
Power Supply
1.Charge protection
When the Battery modules are charged to full, they will communicate
with BMU, and the BMU has the capability to turn off the charger or
open the main contactor. The battery module itself does not have
any switch to disconnect the charger.
2.Balancing
The intra-module balancing circuit is used to compensate slight
capacity imbalance among the four cell blocks within a battery
module.
The inter-module balancing circuit is used to compensate slight
capacity imbalance between different battery modules in series
connection.
3.State of Charge Measurement
Individual cell block voltage and charge/discharge current will be
used to monitor the state of charge (SOC) of the battery module.
The estimated capacity used for the calculations will be adjusted
to meet the capacity of the lowest capacity cell block when the
battery system is fully cycled. The state of charge will be
adjusted for normal self discharge of the battery system when the
unit is not on charge.
4.RS-485 Communication Uplink
RS-485 Communications will be used to communicate with the Battery
Management Unit (BMU) or connection to other battery Modules.
5.RS-485 Communication Downlink
RS-485 Communication connection from Downstream battery module.
6.Status LED
A Dual LED on module to indicate working status. One is green and
the other one is red. Blinking of the green LED indicates that the
module is working properly. Blinking of the red LED indicates that
the module has failure and needs service.
Application
Packing Picture
The battery pack put into spcially foam shelf and then put into the
wooden pallet
Similar Production Picture
Maybe you are interested bigger voltage and capacity battery pack
TAC support suitable and competitive solar energy storage battery
LFP Li-Ion for rural area installations
48v Lifepo4 Battery for EV and ESS
